🔥 Get Full Catalog

Rosenberg DRAE 500 Alternative — LONGWELL LWAE3G500

Looking for an alternative for Rosenberg DRAE 500-4-4D? The LONGWELL LWAE3G500 is the same-size alternative — same control protocol, mounting dimensions on the LONGWELL drawing, performance characterized using AMCA 210/211 test methods (test report on request) — at 40–55% lower landed cost with 15–30 day delivery vs 10–16 weeks ex-works Rosenberg. Widely deployed across CRAH retrofit, large AHU, BESS container.

Replaces: Rosenberg DRAE 500-4-4D Diameter: Ø500 mm Family: DRAE series → LONGWELL LWBE3G / LWAE3G / LWHV / LWFC Sample: 1–3 days
Replacing
Rosenberg
DRAE 500
DRAE series · EC plug fan · Ø500 mm
→
With
LONGWELL
LWAE3G500
Same size class (Ø500 mm) — mounting per drawing · Same control · 15–30 day delivery

Specification Comparison

Specification Rosenberg DRAE 500 LONGWELL LWAE3G500
Fan type EC plug fan EC plug fan
Impeller diameter Ø500 mm Ø500 mm 9 models
Airflow range 1,200–8,200 m³/h up to 10,506 m³/h
Static pressure (max) 1,800 Pa up to 330 Pa
Motor power (max) 3,000 W up to 850 W
Noise floor (Lw) 37 dB(A) from 56 dB(A) (nameplate, per model)
Voltage 380–480 V 3Φ 220–230 V 1Φ · 380–400 V 3Φ
Control input 0–10 V / PWM / Modbus / EC-Control 0–10 V / PWM / Modbus RTU (RS485)
IP rating IP54 / IP55 IP54 std · IP55 / IP67 option
Certifications CE · UL · VDE · EAC CE · RoHS · REACH · ETL on request
Sample lead time 4–10 weeks 1–3 days
Series lead time (≤500 units) 10–16 weeks 15–30 days
Landed cost index (LONGWELL = 100) 175–200 100 (baseline)
Verify it on the LONGWELL selector: all 9 LWAE3G500 models — data, measured curves, drawings · LWAE3G500TS-5MEW-03 (largest airflow in the series) · check your own duty point · samples, MOQ and lead time

Matched to Rosenberg DRAE 500-4-4D by impeller size and fan type — LONGWELL model LWAE3G500 ← DRAE 500. Confirm the mounting footprint against the dimensioned drawing on the model page.

Why Engineers Switch from DRAE 500 to LWAE3G500

4–8× Faster Delivery

15–30 days
vs 10–16 weeks ex-works for Rosenberg in 2026. Sample units 1–3 days from stock vs 4–10 weeks.

40–55% Lower Landed Cost

−€600 to −€2,400
per unit at equivalent spec, depending on size and quantity. On a 50-unit FanGrid retrofit, typical CapEx delta is €30k–€120k.

Drop-in Candidate · Same Size Class

Ø500 mm
Same impeller size and control protocol; confirm the mounting hole pattern and inlet ring against the LONGWELL drawing before ordering.

Drop-in compatibility: what matches and what to confirm

Mechanical match

The LONGWELL LWAE3G500 matches the Rosenberg DRAE 500 mounting pattern (M-mount, ISO 9001 plenum-fan footprint) per the mounting dimensions on the LONGWELL drawing. Inlet ring diameter, motor shaft height, and electrical termination box position are identical. In most retrofits no plate modification is needed — confirm the mounting dimensions against the LONGWELL drawing before ordering.

Electrical & control match

The LWAE3G500 accepts the same 0–10 V analog speed reference, PWM (1 kHz), and Modbus RTU (RS485) control signals as Rosenberg DRAE 500. LONGWELL supplies its Modbus RTU register map with the fan so the BMS points can be re-mapped; the register addresses are not identical to the Rosenberg map.For ebm-papst-specific bus protocols (EC-Control), ask LONGWELL engineering for the integration options.

Performance match

The measured P-Q curve of every LONGWELL model is on its model page; we check your duty point against it before quoting.

Typical Applications

The LWAE3G500 is widely deployed across CRAH retrofit, large AHU, BESS container. Common application categories include:

  • CRAH retrofit
  • Large AHU
  • BESS

Particularly suited for CRAH retrofit and ECFanGrid replacement programs.

FAQ

Is LONGWELL LWAE3G500 a true drop-in replacement for Rosenberg DRAE 500?
Same size class and control interface. Confirm the mounting hole pattern, inlet ring diameter and shaft height against the dimensioned drawing on the LONGWELL LWAE3G500 model page before ordering; it accepts the same 0–10 V analog / PWM / Modbus RTU control signals and is offered in the voltages listed in the table above.
How does LWAE3G500 compare on efficiency to DRAE 500?
LONGWELL does not publish a single peak-efficiency figure for the LWAE3G500. The model page on the selection site gives airflow, static pressure and input power along the curve (measured where marked, nameplate-estimated otherwise), so the efficiency at your duty point follows directly; a test report for a specific model is available from engineering on request.
What’s the 2026 lead time difference?
As of May 2026: Rosenberg DRAE 500 requires 10–16 weeks ex-works due to ongoing allocation. LONGWELL LWAE3G500 ships in 15–30 days for orders up to 500 units and 6–10 weeks for 1,000+ unit OEM programs. Sample units ship in 1–3 days from stocked Ø500 mm inventory.
What’s the cost delta?
At equivalent specification (same Ø, same airflow/Pa, same IP, same control), LONGWELL LWAE3G500 typically lands at 40–55% below Rosenberg DRAE 500 ex-works pricing. Final pricing depends on quantity, voltage, IP rating, and control protocol options.
What applications is LWAE3G500 typically used for?
LWAE3G500 is widely deployed across CRAH retrofit, large AHU, BESS container. Particularly suited for CRAH retrofit and ECFanGrid replacement programs.

Replace your DRAE 500 — samples in 1–3 days

Send a quick request — model + quantity + delivery address. Sample unit ships in 1–3 days for field validation. Series production at 15–30 day lead time after PO.

Request Sample View Full Cross-Reference Table
Official Product Page
Browse the full Backward-Curved Centrifugal EC Fans range on longwellfans.com — request a quote on LWAE3G500 directly.
View on longwellfans.com →
Rosenberg® is a trademark of its owner. LONGWELL is an independent manufacturer and is not affiliated with, endorsed by, or sponsored by Rosenberg. This page is published as engineering reference based on public datasheets. All performance figures reflect specific test conditions; final selection should be confirmed by duty point, voltage/control, mounting and project validation.